SLLSFV1 March 2025 MCF8329A-Q1
PRODUCTION DATA
- 1
- 1 Features
- 2 Applications
- 3 Description
- 4 Pin Configuration and Functions
- 5 Specifications
-
6 Detailed Description
- 6.1 Overview
- 6.2 Functional Block Diagram
- 6.3
Feature Description
- 6.3.1 Three Phase BLDC Gate Drivers
- 6.3.2 Gate Drive Architecture
- 6.3.3 AVDD Linear Voltage Regulator
- 6.3.4 Low-Side Current Sense Amplifier
- 6.3.5 Device Interface Modes
- 6.3.6 Motor Control Input Options
- 6.3.7 Bootstrap Capacitor Initial Charging
- 6.3.8 Starting the Motor Under Different Initial Conditions
- 6.3.9 Motor Start Sequence (MSS)
- 6.3.10 Closed Loop Operation
- 6.3.11 Maximum Torque Per Ampere (MTPA) Control
- 6.3.12 Flux Weakening Control
- 6.3.13 Motor Parameters
- 6.3.14 Motor Parameter Extraction Tool (MPET)
- 6.3.15 Anti-Voltage Surge (AVS)
- 6.3.16 Active Braking
- 6.3.17 Output PWM Switching Frequency
- 6.3.18 Dead Time Compensation
- 6.3.19 Voltage Sense Scaling
- 6.3.20 Motor Stop Options
- 6.3.21 FG Configuration
- 6.3.22 DC Bus Current Limit
- 6.3.23
Protections
- 6.3.23.1 PVDD Supply Undervoltage Lockout (PVDD_UV)
- 6.3.23.2 AVDD Power on Reset (AVDD_POR)
- 6.3.23.3 GVDD Undervoltage Lockout (GVDD_UV)
- 6.3.23.4 BST Undervoltage Lockout (BST_UV)
- 6.3.23.5 MOSFET VDS Overcurrent Protection (VDS_OCP)
- 6.3.23.6 VSENSE Overcurrent Protection (SEN_OCP)
- 6.3.23.7 Thermal Shutdown (OTSD)
- 6.3.23.8 Hardware Lock Detection Current Limit (HW_LOCK_ILIMIT)
- 6.3.23.9 Lock Detection Current Limit (LOCK_ILIMIT)
- 6.3.23.10 Motor Lock (MTR_LCK)
- 6.3.23.11 Motor Lock Detection
- 6.3.23.12 MPET Faults
- 6.3.23.13 IPD Faults
- 6.4 Device Functional Modes
- 6.5 External Interface
- 6.6 EEPROM access and I2C interface
- 7 EEPROM (Non-Volatile) Register Map
- 8 RAM (Volatile) Register Map
- 9 Application and Implementation
- 10Device and Documentation Support
- 11Revision History
- 12Mechanical, Packaging, and Orderable Information
封裝選項
機械數據 (封裝 | 引腳)
- RRY|32
散熱焊盤機械數據 (封裝 | 引腳)
- RRY|32
訂購信息
6.3.20.2 Recirculation Mode
Recirculation mode is configured by setting MTR_STOP to 001b. In order to prevent the inductive energy from returning to DC input supply during motor stop, the MCF8329A-Q1 allows current to circulate within the external MOSFETs by selectively turning OFF some of the active (ON) MOSFETs for a certain time (auto calculated recirculation time to allow the inductive current to decay to zero) before transitioning into Hi-Z by turning OFF the remaining MOSFETs.
Depending on the phase voltage pattern at the time of receiving the stop command, either low-side (see Figure 6-38) or high-side recirculation (see Figure 6-39) will be used to stop the motor without sending the inductive energy back to the DC input supply.
Figure 6-38 Low-Side Recirculation
Figure 6-39 High-Side Recirculation- Recirculation stop is not supported when the motor is in flux weakening zone or MTPA or in active brake mode, and when motor is in any of these states then recirculation stop mode is over written with Hi-Z.
- Recirculation mode is not supported in modulation index control mode and TI recommends to use other stop modes if modulation index control mode is used.