ZHCSHY8 March   2018 LP87561-Q1 , LP87562-Q1 , LP87563-Q1 , LP87564-Q1 , LP87565-Q1

PRODUCTION DATA.  

1. 1 特性
2. 2 應用
3. 3 說明
   1.     效率與輸出電流間的關系
4. 4 修訂歷史記錄
5. 5 Device Comparison Table
6. 6 Pin Configuration and Functions
   1.     Pin Functions
7. 7 Specifications
   1. 7.1 Absolute Maximum Ratings
   2. 7.2 ESD Ratings
   3. 7.3 Recommended Operating Conditions
   4. 7.4 Thermal Information
   5. 7.5 Electrical Characteristics
   6. 7.6 I2C Serial Bus Timing Requirements
   7. 7.7 Typical Characteristics
8. 8 Detailed Description
   1. 8.1 Overview
   2. 8.2 Functional Block Diagram
   3. 8.3 Feature Descriptions
      1. 8.3.1 Multi-Phase DC/DC Converters
         1. 8.3.1.1 Overview
         2. 8.3.1.2 Multiphase Operation, Phase Adding, and Phase-Shedding
         3. 8.3.1.3 Transition Between PWM and PFM Modes
         4. 8.3.1.4 Multiphase Switcher Configurations
         5. 8.3.1.5 Buck Converter Load-Current Measurement
         6. 8.3.1.6 Spread-Spectrum Mode
      2. 8.3.2 Sync Clock Functionality
      3. 8.3.3 Power-Up
      4. 8.3.4 Regulator Control
         1. 8.3.4.1 Enabling and Disabling Regulators
         2. 8.3.4.2 Changing Output Voltage
      5. 8.3.5 Enable and Disable Sequences
      6. 8.3.6 Device Reset Scenarios
      7. 8.3.7 Diagnosis and Protection Features
         1. 8.3.7.1 Power-Good Information (PGOOD Pin)
         2. 8.3.7.2 Warnings for Diagnosis (Interrupt)
            1. 8.3.7.2.1 Output Power Limit
            2. 8.3.7.2.2 Thermal Warning
         3. 8.3.7.3 Protection (Regulator Disable)
            1. 8.3.7.3.1 Short-Circuit and Overload Protection
            2. 8.3.7.3.2 Overvoltage Protection
            3. 8.3.7.3.3 Thermal Shutdown
         4. 8.3.7.4 Fault (Power Down)
            1. 8.3.7.4.1 Undervoltage Lockout
      8. 8.3.8 GPIO Signal Operation
      9. 8.3.9 Digital Signal Filtering
   4. 8.4 Device Functional Modes
      1. 8.4.1 Modes of Operation
   5. 8.5 Programming
      1. 8.5.1 I2C-Compatible Interface
         1. 8.5.1.1 Data Validity
         2. 8.5.1.2 Start and Stop Conditions
         3. 8.5.1.3 Transferring Data
         4. 8.5.1.4 I2C-Compatible Chip Address
         5. 8.5.1.5 Auto-Increment Feature
   6. 8.6 Register Maps
      1. 8.6.1 Register Descriptions
         1. 8.6.1.1  OTP_REV
         2. 8.6.1.2  BUCK0_CTRL1
         3. 8.6.1.3  BUCK0_CTRL2
         4. 8.6.1.4  BUCK1_CTRL1
         5. 8.6.1.5  BUCK1_CTRL2
         6. 8.6.1.6  BUCK2_CTRL1
         7. 8.6.1.7  BUCK2_CTRL2
         8. 8.6.1.8  BUCK3_CTRL1
         9. 8.6.1.9  BUCK3_CTRL2
         10. 8.6.1.10 BUCK0_VOUT
         11. 8.6.1.11 BUCK0_FLOOR_VOUT
         12. 8.6.1.12 BUCK1_VOUT
         13. 8.6.1.13 BUCK1_FLOOR_VOUT
         14. 8.6.1.14 BUCK2_VOUT
         15. 8.6.1.15 BUCK2_FLOOR_VOUT
         16. 8.6.1.16 BUCK3_VOUT
         17. 8.6.1.17 BUCK3_FLOOR_VOUT
         18. 8.6.1.18 BUCK0_DELAY
         19. 8.6.1.19 BUCK1_DELAY
         20. 8.6.1.20 BUCK2_DELAY
         21. 8.6.1.21 BUCK3_DELAY
         22. 8.6.1.22 GPIO2_DELAY
         23. 8.6.1.23 GPIO3_DELAY
         24. 8.6.1.24 RESET
         25. 8.6.1.25 CONFIG
         26. 8.6.1.26 INT_TOP1
         27. 8.6.1.27 INT_TOP2
         28. 8.6.1.28 INT_BUCK_0_1
         29. 8.6.1.29 INT_BUCK_2_3
         30. 8.6.1.30 TOP_STAT
         31. 8.6.1.31 BUCK_0_1_STAT
         32. 8.6.1.32 BUCK_2_3_STAT
         33. 8.6.1.33 TOP_MASK1
         34. 8.6.1.34 TOP_MASK2
         35. 8.6.1.35 BUCK_0_1_MASK
         36. 8.6.1.36 BUCK_2_3_MASK
         37. 8.6.1.37 SEL_I_LOAD
         38. 8.6.1.38 I_LOAD_2
         39. 8.6.1.39 I_LOAD_1
         40. 8.6.1.40 PGOOD_CTRL1
         41. 8.6.1.41 PGOOD_CTRL2
         42. 8.6.1.42 PGOOD_FLT
         43. 8.6.1.43 PLL_CTRL
         44. 8.6.1.44 PIN_FUNCTION
         45. 8.6.1.45 GPIO_CONFIG
         46. 8.6.1.46 GPIO_IN
         47. 8.6.1.47 GPIO_OUT
9. 9 Application and Implementation
   1. 9.1 Application Information
   2. 9.2 Typical Applications
      1. 9.2.1 Design Requirements
         1. 9.2.1.1 Inductor Selection
         2. 9.2.1.2 Input Capacitor Selection
         3. 9.2.1.3 Output Capacitor Selection
         4. 9.2.1.4 Snubber Components
         5. 9.2.1.5 Supply Filtering Components
         6. 9.2.1.6 Current Limit vs. Maximum Output Current
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curves
10. 10Power Supply Recommendations
11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
12. 12器件和文檔支持
    1. 12.1 器件支持
       1. 12.1.1 Third-Party Products Disclaimer
    2. 12.2 文檔支持
    3. 12.3 相關鏈接
    4. 12.4 接收文檔更新通知
    5. 12.5 社區資源
    6. 12.6 商標
    7. 12.7 靜電放電警告
    8. 12.8 Glossary
13. 13"機械、封裝和可訂購信息