日韩一卡2卡三卡4卡无卡网站,人与人和人与物XXX,伊在人线香蕉观看最新2018

ZHCSU17F March 2009 – April 2024 TPS798-Q1

PRODUCTION DATA

封裝選項

機械數據 (封裝 | 引腳)

DGN|8
- MPDS046G

散熱焊盤機械數據 (封裝 | 引腳)

DGN|8
- PPTD076G

訂購信息

5.5 Electrical Characteristics

V_IN = V_OUT(NOM) + 1V or 4V (whichever is greater for either fixed or adjustable versions), I_LOAD = 1mA, V_EN = 3V, and C_OUT = C_IN = 2.2μF (unless otherwise noted); for the TPS79801, the FB pin is tied to V_OUT; typical values are at T_J = 25°C

PARAMETER		TEST CONDITIONS		T_J⁽¹⁾	MIN	TYP	MAX	UNIT
V_IN	Minimum input voltage	I_LOAD = 50mA		Full range		3	4	V
Fixed V_OUT	Initial output voltage accuracy	V_IN = V_OUT nom + 0.5V		25°C	–1.5%		1.5%
Fixed V_OUT	Output voltage accuracy over line, load, and full temperature range	V_IN = V_OUT nom + 1V to 50V, I_LOAD = 1mA to 50mA		Full range	–3%		3%
Adjustable V_OUT	Initial output voltage accuracy	V_IN = 3V		25°C	1.256	1.275	1.294	V
Adjustable V_OUT	Output voltage accuracy over line, load, and full temperature range	V_IN = 4V to 50V, I_LOAD = 1mA to 50mA		Full range	1.237	1.275	1.313	V
ΔV_OUT/ΔV_IN	Line regulation, adjustable V_OUT	ΔV_IN = 3V to 50V		Full range			13	mV
ΔV_OUT/ΔV_IN	Line regulation, TPS79850	V_IN = V_OUT nom + 0.5V to 50V		Full range			15	mV
ΔV_OUT/ΔI_OUT	Load regulation, adjustable V_OUT	ΔI_LOAD = 1mA to 50mA		25°C			20	mV
	Load regulation, adjustable V_OUT	ΔI_LOAD = 1mA to 50mA		Full range			32	mV
	Load regulation, fixed V_OUT	ΔI_LOAD = 1mA to 50mA		25°C			50	mV
	Load regulation, fixed V_OUT	ΔI_LOAD = 1mA to 50mA		Full range			90	mV
Adjustable V_OUT	Output voltage range⁽²⁾ ⁽³⁾			Full range	1.275		28	V
V_DO	Dropout voltage⁽⁴⁾ ⁽⁵⁾	V_IN = V_OUT(NOM) – 0.1V		25°C		85	150	mV
		V_IN = V_OUT(NOM) – 0.1V		Full range			190
		I_LOAD = 10mA, V_IN = V_OUT(NOM) – 0.1V		25°C		170	260
		I_LOAD = 10mA, V_IN = V_OUT(NOM) – 0.1V		Full range			350
		I_LOAD = 50mA, V_IN = V_OUT(NOM) – 0.1V		25°C		300	370
		I_LOAD = 50mA, V_IN = V_OUT(NOM) – 0.1V		Full range			550
I_GND	GND pin current⁽⁶⁾	V_IN = V_OUT(NOM)	I_LOAD = 0mA	Full range		30	80	μA
			I_LOAD = 1mA	Full range		100	180
			I_LOAD = 10mA	Full range		400	700
			I_LOAD = 50mA	Full range		1.8	3.3	mA
V_N	Output voltage noise	C_OUT = 10μF, I_LOAD = 50mA, BW = 10Hz to 100kHz, V_IN = 4.3V, V_OUT = 3.3V (adjustable used)		25°C		100		μV_RMS
I_FB	FB pin bias current⁽⁷⁾	V_IN = 3V		25°C		0.05	0.2	μA
V_EN	EN pin high (enabled)⁽⁸⁾	OFF to ON, V_IN = 6V		Full range			1.5	V
	EN pin low (shutdown)⁽⁸⁾	ON to OFF, V_IN = 6V		25°C	0.4 V			V
	EN pin low (shutdown)⁽⁸⁾	ON to OFF, V_IN = 6V		Full range	0.2 V			V
I_EN	EN pin current⁽⁸⁾	V_EN = 0V V_IN = 6V, I_LOAD = 0mA		Full range		0.4	2	μA
I_EN	EN pin current⁽⁸⁾	V_EN = 3V, V_IN = 6V, I_LOAD = 0mA		Full range		0.4	0.5	μA
I_shutdown	GND pin current⁽⁶⁾	V_IN = 6V, V_EN = 0V, I_LOAD = 0mA		Full range		3	25	μA
PSRR	Power-supply rejection ratio	V_IN = 4.3V, V_OUT 3.3V V_RIPPLE = 0.5V_PP, f_RIPPLE = 120Hz, I_LOAD = 50mA		25°C		65		dB
I_LIMIT	Fixed current limit⁽⁹⁾	ΔV_OUT = V_OUT(NOM) – 0.1V		Full range	60		200	mA
I_LIMIT	Adjustable current limit	ΔV_OUT = V_OUT(NOM) – 0.1V		Full range	60		200	mA
I_RL	Input reverse leakage current(reverse battery test)	V_IN = –60V, V_OUT = open, C_IN open		Full range			6	mA
I_RO	Reverse output current⁽¹⁰⁾	V_OUT = V_OUT(NOM), V_IN = ground		25°C		19	25	μA
T_SD	Thermal shutdown temperature (T_J)⁽¹¹⁾	Shutdown, temperature increasing			135			°C
T_SD	Thermal shutdown temperature (T_J)⁽¹¹⁾	Reset, temperature decreasing			135			°C

(1) Full range T_J = –40°C to 125°C.

(2) This parameter is tested and specified under pulse load conditions such that T_J = T_A. This device is 100% production tested at T_A = 25°C. Performance at full range is specified by design, characterization, bench to ATE correlation testing, and other statistical process controls.

(4) This device is limited by a maximum junction temperature of T_J = 125°C. The regulated output voltage specification cannot be applied to all combinations of various V_IN, V_OUT, ambient temperature, and I_OUT conditions. When operating with large voltage differentials across the device, the output load must be limited so as not to violate the maximum junction temperature for a given ambient temperature.

(5) In the adjustable version test, the output uses an external voltage divider. This resistor voltage divider is made up of R₁ = 215k? and R2 (bottom resistor) = 340k?. This configuration preloads the output with 6μA.

(6) By definition, dropout voltage is the minimum input voltage needed to maintain a given output voltage at a specific load current. For dropout testing, minimum V_IN = V_OUT(NOM) × 0.96. This specification ensures that the device is in dropout and takes into account the output voltage tolerance over the full temperature range.

(7) Ground pin current is tested with V_IN = V_OUT(NOM) or 3V, whichever is greater.

(8) FB pin current flows into the FB pin.

(9) EN pin current flows into the EN pin.

(10) Current limit is tested with V_IN = V_OUT(NOM) + 0.5V or 3V, whichever is greater. V_OUT is forced to V_OUT(NOM) – 0.1V and the output current is measured.

(11) Reverse output current is tested with the IN pin tied to ground and the output forced to V_OUT(NOM) +0.1V. This current flows into the OUT pin and out of the GND pin and then measured.

(12) Specified by design.