4 修訂歷史記錄
Changes from A Revision (March 2018) to B Revision
- 通篇進行了編輯性和修飾性更改Go
- 在特性中添加了“穩健可靠的隔離柵”項目符號Go
- 在特性中添加了“在 1kVRMS 工作電壓下，預計壽命超過 100 年”項目符號Go
- 在特性中添加了“高達 5000V 的 RMS 隔離額定值”項目符號Go
- 在特性中添加了“高達 10kVPK 的浪涌保護能力”項目符號Go
- 在特性中添加了“±8kV IEC 61000-4-2 跨隔離柵接觸放電保護”項目符號Go
- 在特性和Insulation Specifications表中將 VDE 標準名稱從“DIN V VDE V 0884-11:2017-01”更改為“DIN VDE V 0884-11:2017-01”Go
- 向“特性”中的信息的 TUV 認證項目符號中添加了“EN 62368-1”標準Go
- 刪除了“為選定的器件提供了汽車級版本”中的“已計劃進行所有機構認證”項目符號Go
- 更新了簡化原理圖，以顯示信號隔離通道的兩個串聯隔離電容器，而不是單個電容器Go
- Added "Contact discharge per IEC 61000-4-2; Isolation barrier withstand test" specification of ±8000 in ESD Ratings tableGo
- Added table note "IEC ESD strike is applied across the barrier with all pins on each side tied together creating a two-terminal device" to ESD Ratings tableGo
- Deleted "TJ or Junction temperature" parameter from Recommended Operating Conditions table as it is already specified in Absolute Maximum Ratings tableGo
- Added "See Figure 34" to TEST CONDITIONS of VIOWM specificationGo
- Updated Safety-Related Certifications table Go
- Added the following note to Figure 25: "Optional 100 µF capacitor can be added between VCC and GND1; refer to Power Supply Recommendations" Go
- Added the following note to Figure 30: "Optional 100 µF capacitor can be added between VCC and GND1; refer to Power Supply Recommendations" Go
- Added the following text to Design Requirements: "Optional 100 µF decoupling capacitor can be added between VCC and GND1 pins; refer to Power Supply Recommendations for more details"Go
- Added text to Power Supply Recommendations section to emphasise that input decoupling capacitor should be larger than output capacitor by at least 100 µF Go
- Added the following note to Figure 35: "Optional 100 µF capacitor can be added between VCC and GND1; refer to Power Supply Recommendations" Go
Changes from * Revision (November 2017) to A Revision
- Changed OUTB to pin 4 and INB to pin 13 in the Pin Functions tableGo