SN74LVTH574

正在供貨

具有三態輸出的 3.3V ABT 八路邊沿 D 類觸發器

產品詳情

Number of channels 8 Technology family LVT Supply voltage (min) (V) 2.7 Supply voltage (max) (V) 3.6 Input type TTL-Compatible CMOS Output type 3-State Clock frequency (max) (MHz) 150 IOL (max) (mA) 64 IOH (max) (mA) -32 Supply current (max) (μA) 5000 Features Bus-hold, Over-voltage tolerant inputs, Partial power down (Ioff), Power up 3-state, Ultra high speed (tpd <5ns) Operating temperature range (°C) -40 to 85 Rating Catalog
Number of channels 8 Technology family LVT Supply voltage (min) (V) 2.7 Supply voltage (max) (V) 3.6 Input type TTL-Compatible CMOS Output type 3-State Clock frequency (max) (MHz) 150 IOL (max) (mA) 64 IOH (max) (mA) -32 Supply current (max) (μA) 5000 Features Bus-hold, Over-voltage tolerant inputs, Partial power down (Ioff), Power up 3-state, Ultra high speed (tpd <5ns) Operating temperature range (°C) -40 to 85 Rating Catalog
SOIC (DW) 20 131.84 mm2 12.8 x 10.3 SOP (NS) 20 98.28 mm2 12.6 x 7.8 SSOP (DB) 20 56.16 mm2 7.2 x 7.8 TSSOP (PW) 20 41.6 mm2 6.5 x 6.4 VQFN (RGY) 20 15.75 mm2 4.5 x 3.5
  • Support Mixed-Mode Signal Operation (5-V Input and Output Voltages With 3.3-V VCC)
  • Support Unregulated Battery Operation Down to 2.7 V
  • Typical VOLP (Output Ground Bounce)
       <0.8 V at VCC = 3.3 V, TA = 25°C
  • Ioff and Power-Up 3-State Support Hot Insertion
  • Bus Hold on Data Inputs Eliminates the Need for External Pullup/Pulldown Resistors
  • Latch-Up Performance Exceeds 500 mA Per JESD 17
  • ESD Protection Exceeds JESD 22
    • 2000-V Human-Body Model (A114-A)
    • 200-V Machine Model (A115-A)
  • Support Mixed-Mode Signal Operation (5-V Input and Output Voltages With 3.3-V VCC)
  • Support Unregulated Battery Operation Down to 2.7 V
  • Typical VOLP (Output Ground Bounce)
       <0.8 V at VCC = 3.3 V, TA = 25°C
  • Ioff and Power-Up 3-State Support Hot Insertion
  • Bus Hold on Data Inputs Eliminates the Need for External Pullup/Pulldown Resistors
  • Latch-Up Performance Exceeds 500 mA Per JESD 17
  • ESD Protection Exceeds JESD 22
    • 2000-V Human-Body Model (A114-A)
    • 200-V Machine Model (A115-A)

These octal flip-flops are designed specifically for low-voltage (3.3-V) VCC operation, but with the capability to provide a TTL interface to a 5-V system environment.

The eight flip-flops of the ’LVTH574 devices are edge-triggered D-type flip-flops. On the positive transition of the clock (CLK) input, the Q outputs are set to the logic levels set up at the data (D) inputs.

A buffered output-enable (OE\) input can be used to place the eight outputs in either a normal logic state (high or low logic levels) or a high-impedance state. In the high-impedance state, the outputs neither load nor drive the bus lines significantly. The high-impedance state and increased drive provide the capability to drive bus lines without need for interface or pullup components.

OE\ does not affect the internal operations of the flip-flops. Old data can be retained or new data can be entered while the outputs are in the high-impedance state.

To ensure the high-impedance state during power up or power down, OE\ should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

Active bus-hold circuitry is provided to hold unused or floating data inputs at a valid logic level. Use of pullup or pulldown resistors with the bus-hold circuitry is not recommended.

These devices are fully specified for hot-insertion applications using Ioff and power-up 3-state. The Ioff circuitry disables the outputs, preventing damaging current backflow through the devices when they are powered down. The power-up 3-state circuitry places the outputs in the high-impedance state during power up and power down, which prevents driver conflict.

These octal flip-flops are designed specifically for low-voltage (3.3-V) VCC operation, but with the capability to provide a TTL interface to a 5-V system environment.

The eight flip-flops of the ’LVTH574 devices are edge-triggered D-type flip-flops. On the positive transition of the clock (CLK) input, the Q outputs are set to the logic levels set up at the data (D) inputs.

A buffered output-enable (OE\) input can be used to place the eight outputs in either a normal logic state (high or low logic levels) or a high-impedance state. In the high-impedance state, the outputs neither load nor drive the bus lines significantly. The high-impedance state and increased drive provide the capability to drive bus lines without need for interface or pullup components.

OE\ does not affect the internal operations of the flip-flops. Old data can be retained or new data can be entered while the outputs are in the high-impedance state.

To ensure the high-impedance state during power up or power down, OE\ should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

Active bus-hold circuitry is provided to hold unused or floating data inputs at a valid logic level. Use of pullup or pulldown resistors with the bus-hold circuitry is not recommended.

These devices are fully specified for hot-insertion applications using Ioff and power-up 3-state. The Ioff circuitry disables the outputs, preventing damaging current backflow through the devices when they are powered down. The power-up 3-state circuitry places the outputs in the high-impedance state during power up and power down, which prevents driver conflict.
下載 觀看帶字幕的視頻 視頻

您可能感興趣的相似產品

功能與比較器件相同，且具有相同引腳
CD74ACT374 正在供貨 具有三態輸出的八路 D 類觸發器 Voltage range (4.5V to 5.5V)

技術文檔

star =有關此產品的 TI 精選熱門文檔
未找到結果。請清除搜索并重試。
查看全部 20
類型 標題 下載最新的英語版本 日期
* 數據表 SN54LVTH574, SN74LVTH574 數據表 (Rev. G) 2003年 9月 15日
應用手冊 慢速或浮點 CMOS 輸入的影響 (Rev. E) PDF | HTML 英語版 (Rev.E) 2025年 3月 26日
應用手冊 Power-Up Behavior of Clocked Devices (Rev. B) PDF | HTML 2022年 12月 15日
應用手冊 An Overview of Bus-Hold Circuit and the Applications (Rev. B) 2018年 9月 17日
選擇指南 Logic Guide (Rev. AB) 2017年 6月 12日
應用手冊 Understanding and Interpreting Standard-Logic Data Sheets (Rev. C) 2015年 12月 2日
選擇指南 邏輯器件指南 2014 (Rev. AA) 最新英語版本 (Rev.AC) PDF | HTML 2014年 11月 17日
選擇指南 《高級總線接口邏輯器件選擇指南》 英語版 2010年 7月 7日
用戶指南 LOGIC Pocket Data Book (Rev. B) 2007年 1月 16日
應用手冊 Semiconductor Packing Material Electrostatic Discharge (ESD) Protection 2004年 7月 8日
應用手冊 TI IBIS File Creation, Validation, and Distribution Processes 2002年 8月 29日
應用手冊 16-Bit Widebus Logic Families in 56-Ball, 0.65-mm Pitch Very Thin Fine-Pitch BGA (Rev. B) 2002年 5月 22日
應用手冊 Power-Up 3-State (PU3S) Circuits in TI Standard Logic Devices 2002年 5月 10日
應用手冊 LVT-to-LVTH Conversion 1998年 12月 8日
應用手冊 LVT Family Characteristics (Rev. A) 1998年 3月 1日
應用手冊 Bus-Interface Devices With Output-Damping Resistors Or Reduced-Drive Outputs (Rev. A) 1997年 8月 1日
應用手冊 Input and Output Characteristics of Digital Integrated Circuits 1996年 10月 1日
應用手冊 Live Insertion 1996年 10月 1日
應用手冊 Understanding Advanced Bus-Interface Products Design Guide 1996年 5月 1日
選擇指南 Logic Guide (Rev. AC) PDF | HTML 1994年 6月 1日

設計和開發

如需其他信息或資源，請點擊以下任一標題進入詳情頁面查看（如有）。

評估板

14-24-LOGIC-EVM — 采用 14 引腳至 24 引腳 D、DB、DGV、DW、DYY、NS 和 PW 封裝的邏輯產品通用評估模塊

14-24-LOGIC-EVM 評估模塊 (EVM) 設計用于支持采用 14 引腳至 24 引腳 D、DW、DB、NS、PW、DYY 或 DGV 封裝的任何邏輯器件。

用戶指南: PDF | HTML
英語版 (Rev.B): PDF | HTML
TI.com 上無現貨
評估板

14-24-NL-LOGIC-EVM — 采用 14 引腳至 24 引腳無引線封裝的邏輯產品通用評估模塊

14-24-EVM 是一款靈活的評估模塊 (EVM)，旨在支持具有 14 引腳至 24 引腳 BQA、BQB、RGY、RSV、RJW 或 RHL 封裝的任何邏輯或轉換器件。

用戶指南: PDF | HTML
英語版 (Rev.A): PDF | HTML
TI.com 上無現貨
仿真模型

SN74LVTH574 IBIS Model (Rev. A)

SCBM053A.ZIP (31 KB) - IBIS Model
下載
封裝 引腳 CAD 符號、封裝和 3D 模型
SOIC (DW) 20 Ultra Librarian
SOP (NS) 20 Ultra Librarian
SSOP (DB) 20 Ultra Librarian
TSSOP (PW) 20 Ultra Librarian
VQFN (RGY) 20 Ultra Librarian

訂購和質量

包含信息：
  • RoHS
  • REACH
  • 器件標識
  • 引腳鍍層/焊球材料
  • MSL 等級/回流焊峰值溫度
  • MTBF/時基故障估算
  • 材料成分
  • 鑒定摘要
  • 持續可靠性監測
包含信息：
  • 制造廠地點
  • 封裝廠地點

支持和培訓

視頻