SN54LVC574A

正在供貨

具有三態輸出的八路邊沿 D 類觸發器

產品詳情

Number of channels 8 Technology family LVC Supply voltage (min) (V) 2 Supply voltage (max) (V) 3.6 Input type Standard CMOS Output type 3-State Clock frequency (max) (MHz) 100 IOL (max) (mA) 24 IOH (max) (mA) -24 Supply current (max) (μA) 10 Features Balanced outputs, Over-voltage tolerant inputs, Partial power down (Ioff), Very high speed (tpd 5-10ns) Operating temperature range (°C) -55 to 125 Rating Military
Number of channels 8 Technology family LVC Supply voltage (min) (V) 2 Supply voltage (max) (V) 3.6 Input type Standard CMOS Output type 3-State Clock frequency (max) (MHz) 100 IOL (max) (mA) 24 IOH (max) (mA) -24 Supply current (max) (μA) 10 Features Balanced outputs, Over-voltage tolerant inputs, Partial power down (Ioff), Very high speed (tpd 5-10ns) Operating temperature range (°C) -55 to 125 Rating Military
CDIP (J) 20 167.464 mm2 24.2 x 6.92 CFP (W) 20 90.5828 mm2 13.09 x 6.92
  • Operate From 1.65 V to 3.6 V
  • Inputs Accept Voltages to 5.5 V
  • Specified From -40°C to 85°C, -40°C to 125°C, and -55°C to 125°C
  • Max tpd of 7 ns at 3.3 V
  • Typical VOLP (Output Ground Bounce)
       <0.8 V at VCC = 3.3 V, TA = 25°C
  • Typical VOHV (Output VOH Undershoot)
       >2 V at VCC = 3.3 V, TA = 25°C
  • Support Mixed-Mode Signal Operation on All Ports (5-V Input/Output Voltage With 3.3-V VCC)
  • Ioff Supports Partial-Power-Down Mode Operation
  • Latch-Up Performance Exceeds 250 mA Per JESD 17
  • ESD Protection Exceeds JESD 22
    • 2000-V Human-Body Model (A114-A)
    • 200-V Machine Model (A115-A)
    • 1000-V Charged-Device Model (C101)
  • Operate From 1.65 V to 3.6 V
  • Inputs Accept Voltages to 5.5 V
  • Specified From -40°C to 85°C, -40°C to 125°C, and -55°C to 125°C
  • Max tpd of 7 ns at 3.3 V
  • Typical VOLP (Output Ground Bounce)
       <0.8 V at VCC = 3.3 V, TA = 25°C
  • Typical VOHV (Output VOH Undershoot)
       >2 V at VCC = 3.3 V, TA = 25°C
  • Support Mixed-Mode Signal Operation on All Ports (5-V Input/Output Voltage With 3.3-V VCC)
  • Ioff Supports Partial-Power-Down Mode Operation
  • Latch-Up Performance Exceeds 250 mA Per JESD 17
  • ESD Protection Exceeds JESD 22
    • 2000-V Human-Body Model (A114-A)
    • 200-V Machine Model (A115-A)
    • 1000-V Charged-Device Model (C101)

The SN54LVC574A octal edge-triggered D-type flip-flop is designed for 2.7-V to 3.6-V VCC operation, and the SN74LVC574A octal edge-triggered D-type flip-flop is designed for 1.65-V to 3.6-V VCC operation.

These devices feature 3-state outputs designed specifically for driving highly capacitive or relatively low-impedance loads. They are particularly suitable for implementing buffer registers, I/O ports, bidirectional bus drivers, and working registers.

On the positive transition of the clock (CLK) input, the Q outputs are set to the logic levels at the data (D) inputs.

A buffered output-enable (OE)\ input can be used to place the eight outputs in either a normal logic state (high or low logic levels) or the high-impedance state. In the high-impedance state, the outputs neither load nor drive the bus lines significantly. The high-impedance state and increased drive provide the capability to drive bus lines without interface or pullup components.

OE\ does not affect the internal operations of the flip-flops. Old data can be retained or new data can be entered while the outputs are in the high-impedance state.

These devices are fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down.

To ensure the high-impedance state during power up or power down, OE\ should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

Inputs can be driven from either 3.3-V or 5-V devices. This feature allows the use of these devices as translators in a mixed 3.3-V/5-V system environment.

The SN54LVC574A octal edge-triggered D-type flip-flop is designed for 2.7-V to 3.6-V VCC operation, and the SN74LVC574A octal edge-triggered D-type flip-flop is designed for 1.65-V to 3.6-V VCC operation.

These devices feature 3-state outputs designed specifically for driving highly capacitive or relatively low-impedance loads. They are particularly suitable for implementing buffer registers, I/O ports, bidirectional bus drivers, and working registers.

On the positive transition of the clock (CLK) input, the Q outputs are set to the logic levels at the data (D) inputs.

A buffered output-enable (OE)\ input can be used to place the eight outputs in either a normal logic state (high or low logic levels) or the high-impedance state. In the high-impedance state, the outputs neither load nor drive the bus lines significantly. The high-impedance state and increased drive provide the capability to drive bus lines without interface or pullup components.

OE\ does not affect the internal operations of the flip-flops. Old data can be retained or new data can be entered while the outputs are in the high-impedance state.

These devices are fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down.

To ensure the high-impedance state during power up or power down, OE\ should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

Inputs can be driven from either 3.3-V or 5-V devices. This feature allows the use of these devices as translators in a mixed 3.3-V/5-V system environment.
下載 觀看帶字幕的視頻 視頻

技術文檔

star =有關此產品的 TI 精選熱門文檔
未找到結果。請清除搜索并重試。
查看全部 32
類型 標題 下載最新的英語版本 日期
* 數據表 SN54LVC574A, SN74LVC574A 數據表 (Rev. R) 2005年 3月 14日
* SMD SN54LVC574A SMD 5962-97576 2016年 6月 21日
應用手冊 慢速或浮點 CMOS 輸入的影響 (Rev. E) PDF | HTML 英語版 (Rev.E) 2025年 3月 26日
應用手冊 Power-Up Behavior of Clocked Devices (Rev. B) PDF | HTML 2022年 12月 15日
選擇指南 Little Logic Guide 2018 (Rev. G) 2018年 7月 6日
選擇指南 Logic Guide (Rev. AB) 2017年 6月 12日
應用手冊 How to Select Little Logic (Rev. A) 2016年 7月 26日
應用手冊 Understanding and Interpreting Standard-Logic Data Sheets (Rev. C) 2015年 12月 2日
選擇指南 邏輯器件指南 2014 (Rev. AA) 最新英語版本 (Rev.AC) PDF | HTML 2014年 11月 17日
選擇指南 小尺寸邏輯器件指南 (Rev. E) 最新英語版本 (Rev.G) 2012年 7月 16日
用戶指南 LOGIC Pocket Data Book (Rev. B) 2007年 1月 16日
應用手冊 CMOS 非緩沖反向器在振蕩器電路中的使用 英語版 2006年 3月 23日
應用手冊 選擇正確的電平轉換解決方案 (Rev. A) 英語版 (Rev.A) 2006年 3月 23日
產品概述 Design Summary for WCSP Little Logic (Rev. B) 2004年 11月 4日
應用手冊 Semiconductor Packing Material Electrostatic Discharge (ESD) Protection 2004年 7月 8日
用戶指南 Signal Switch Data Book (Rev. A) 2003年 11月 14日
用戶指南 LVC and LV Low-Voltage CMOS Logic Data Book (Rev. B) 2002年 12月 18日
應用手冊 Texas Instruments Little Logic Application Report 2002年 11月 1日
應用手冊 TI IBIS File Creation, Validation, and Distribution Processes 2002年 8月 29日
更多文獻資料 Standard Linear & Logic for PCs, Servers & Motherboards 2002年 6月 13日
應用手冊 16-Bit Widebus Logic Families in 56-Ball, 0.65-mm Pitch Very Thin Fine-Pitch BGA (Rev. B) 2002年 5月 22日
應用手冊 Power-Up 3-State (PU3S) Circuits in TI Standard Logic Devices 2002年 5月 10日
更多文獻資料 STANDARD LINEAR AND LOGIC FOR DVD/VCD PLAYERS 2002年 3月 27日
應用手冊 Migration From 3.3-V To 2.5-V Power Supplies For Logic Devices 1997年 12月 1日
應用手冊 Bus-Interface Devices With Output-Damping Resistors Or Reduced-Drive Outputs (Rev. A) 1997年 8月 1日
應用手冊 CMOS Power Consumption and CPD Calculation (Rev. B) 1997年 6月 1日
應用手冊 LVC Characterization Information 1996年 12月 1日
應用手冊 Input and Output Characteristics of Digital Integrated Circuits 1996年 10月 1日
應用手冊 Live Insertion 1996年 10月 1日
設計指南 Low-Voltage Logic (LVC) Designer's Guide 1996年 9月 1日
應用手冊 Understanding Advanced Bus-Interface Products Design Guide 1996年 5月 1日
選擇指南 Logic Guide (Rev. AC) PDF | HTML 1994年 6月 1日

設計和開發

如需其他信息或資源，請點擊以下任一標題進入詳情頁面查看（如有）。

封裝 引腳 CAD 符號、封裝和 3D 模型
CDIP (J) 20 Ultra Librarian
CFP (W) 20 Ultra Librarian

訂購和質量

包含信息：
  • RoHS
  • REACH
  • 器件標識
  • 引腳鍍層/焊球材料
  • MSL 等級/回流焊峰值溫度
  • MTBF/時基故障估算
  • 材料成分
  • 鑒定摘要
  • 持續可靠性監測
包含信息：
  • 制造廠地點
  • 封裝廠地點

支持和培訓

視頻