ZHCSNG6 November   2021 UCC28781-Q1

PRODUCTION DATA  

1. 1 特性
2. 2 應(yīng)用
3. 3 說(shuō)明
4. 4 Revision History
5. 5 Pin Configuration and Functions
6. 6 Specifications
   1. 6.1 Absolute Maximum Ratings
   2. 6.2 ESD Ratings
   3. 6.3 Recommended Operating Conditions
   4. 6.4 Thermal Information
   5. 6.5 Electrical Characteristics
   6. 6.6 Typical Characteristics
7. 7 Detailed Description
   1. 7.1 Overview
   2. 7.2 Functional Block Diagram
   3. 7.3 Detailed Pin Description
      1. 7.3.1  BUR Pin (Programmable Burst Mode)
      2. 7.3.2  FB Pin (Feedback Pin)
      3. 7.3.3  REF Pin (Internal 5-V Bias)
      4. 7.3.4  VDD Pin (Device Bias Supply)
      5. 7.3.5  P13 and SWS Pins
      6. 7.3.6  S13 Pin
      7. 7.3.7  IPC Pin (Intelligent Power Control Pin)
      8. 7.3.8  RUN Pin (Driver and Bias Source for Isolator)
      9. 7.3.9  PWMH and AGND Pins
      10. 7.3.10 PWML and PGND Pins
      11. 7.3.11 SET Pin
      12. 7.3.12 RTZ Pin (Sets Delay for Transition Time to Zero)
      13. 7.3.13 RDM Pin (Sets Synthesized Demagnetization Time for ZVS Tuning)
      14. 7.3.14 XCD Pin
      15. 7.3.15 CS, VS, and FLT Pins
   4. 7.4 Device Functional Modes
      1. 7.4.1  Adaptive ZVS Control with Auto-Tuning
      2. 7.4.2  Dead-Time Optimization
      3. 7.4.3  EMI Dither and Dither Fading Function
      4. 7.4.4  Control Law Across Entire Load Range
      5. 7.4.5  Adaptive Amplitude Modulation (AAM)
      6. 7.4.6  Adaptive Burst Mode (ABM)
      7. 7.4.7  Low Power Mode (LPM)
      8. 7.4.8  First Standby Power Mode (SBP1)
      9. 7.4.9  Second Standby Power Mode (SBP2)
      10. 7.4.10 Startup Sequence
      11. 7.4.11 Survival Mode of VDD (INT_STOP)
      12. 7.4.12 System Fault Protections
          1. 7.4.12.1  Brown-In and Brown-Out
          2. 7.4.12.2  Output Over-Voltage Protection (OVP)
          3. 7.4.12.3  Input Over Voltage Protection (IOVP)
          4. 7.4.12.4  Over-Temperature Protection (OTP) on FLT Pin
          5. 7.4.12.5  Over-Temperature Protection (OTP) on CS Pin
          6. 7.4.12.6  Programmable Over-Power Protection (OPP)
          7. 7.4.12.7  Peak Power Limit (PPL)
          8. 7.4.12.8  Output Short-Circuit Protection (SCP)
          9. 7.4.12.9  Over-Current Protection (OCP)
          10. 7.4.12.10 External Shutdown
          11. 7.4.12.11 Internal Thermal Shutdown
      13. 7.4.13 Pin Open/Short Protections
          1. 7.4.13.1 Protections on CS pin Fault
          2. 7.4.13.2 Protections on P13 pin Fault
          3. 7.4.13.3 Protections on RDM and RTZ pin Faults
8. 8 Application and Implementation
   1. 8.1 Application Information
   2. 8.2 Typical Application Circuit
      1. 8.2.1 Design Requirements for a 60-W, 15-V ZVSF Bias Supply Application with a DC Input
      2. 8.2.2 Detailed Design Procedure
         1. 8.2.2.1 Input Bulk Capacitance and Minimum Bulk Voltage
         2. 8.2.2.2 Transformer Calculations
            1. 8.2.2.2.1 Primary-to-Secondary Turns Ratio (NPS)
            2. 8.2.2.2.2 Primary Magnetizing Inductance (LM)
            3. 8.2.2.2.3 Primary Winding Turns (NP)
            4. 8.2.2.2.4 Secondary Winding Turns (NS)
            5. 8.2.2.2.5 Auxiliary Winding Turns (NA)
            6. 8.2.2.2.6 Winding and Magnetic Core Materials
         3. 8.2.2.3 Calculation of ZVS Sensing Network
         4. 8.2.2.4 Calculation of BUR Pin Resistances
         5. 8.2.2.5 Calculation of Compensation Network
      3. 8.2.3 Application Curves
9. 9 Power Supply Recommendations
10. 10Layout
    1. 10.1 Layout Guidelines
       1. 10.1.1  General Considerations
       2. 10.1.2  RDM and RTZ Pins
       3. 10.1.3  SWS Pin
       4. 10.1.4  VS Pin
       5. 10.1.5  BUR Pin
       6. 10.1.6  FB Pin
       7. 10.1.7  CS Pin
       8. 10.1.8  AGND Pin
       9. 10.1.9  PGND Pin
       10. 10.1.10 Thermal Pad
    2. 10.2 Layout Example
11. 11Device and Documentation Support
    1. 11.1 Documentation Support
       1. 11.1.1 Receiving Notification of Documentation Updates
    2. 11.2 支持資源
    3. 11.3 Trademarks
    4. 11.4 Electrostatic Discharge Caution
    5. 11.5 術(shù)語(yǔ)表
12. 12Mechanical, Packaging, and Orderable Information