亚洲精品国产精品制服丝袜 ,亚洲精品久久久久无码AV,91精品免费久久久久久久久

SLVSK53 October 2025 TPS7E82

ADVANCE INFORMATION

封裝選項

機械數據 (封裝 | 引腳)

DBV|5
- MPDS018T

散熱焊盤機械數據 (封裝 | 引腳)

訂購信息

slvsk53_oa

5.5 Electrical Characteristics

Over operating junction temperature range (T_J = –40°C to +150°C), V_IN = 3.0V or V_IN = V_OUT(nom) + 0.5V (whichever is greater), I_OUT = 1mA, V_EN = 2.0V, C_IN = 1.0μF, C_OUT = 4.7μF, and PG pin pulled up-to V_IN with 100kΩ, unless otherwise noted. Typical values are at T_J = 25°C.

PARAMETER		TEST CONDITIONS	MIN	TYP	MAX	UNIT
V_FB	Feedback voltage			1.2		V
V_UVLO+	Rising input supply UVLO	V_IN rising		2.8	2.91	V
V_UVLO-	Falling input supply UVLO	V_IN falling	2.6	2.7		V
V_UVLO(HYST)	V_UVLO hysteresis			100		mV
V_OUT	Output voltage	V_OUT + 2.0V ≤ V_IN ≤ 40V, I_OUT = 35mA, T_J = 25℃	–0.6		0.6	%
		V_OUT + 2.0V ≤ V_IN ≤ 40V, I_OUT = 35mA	–1.2		1.0
		1mA ≤ I_OUT ≤ 300mA, 2.0V ≤ V_IN – V_OUT ≤ 15V	–1.2		1.2
ΔV_OUT(ΔV_IN)	Line regulation	I_OUT = 1mA, V_OUT + 0.5V ≤ V_IN ≤ 40V			6	mV
Δ%V_OUT/ΔV_IN	Line regulation	I_OUT = 1mA, V_OUT + 0.5V ≤ V_IN ≤ 40V			0.02	%/V
ΔV_OUT(ΔI_OUT)	Load regulation	1mA ≤ I_OUT ≤ 300mA, V_IN = V_OUT + 2.0V			17.5	mV
Δ%V_OUT/ΔI_OUT	Load regulation	1mA ≤ I_OUT ≤ 300mA, V_IN = V_OUT + 2.0V			0.375	%/A
V_DO	Dropout voltage	I_OUT = 300mA		0.9	1.8	V
V_DO	Dropout voltage	I_OUT = 300mA, for adjustable		0.9	1.8	V
V_DO	Dropout voltage	I_OUT = 100mA		0.3	0.55	V
V_DO	Dropout voltage	I_OUT = 100mA, for adjustable		0.28	0.6	V
I_LIM	Output current limit	V_OUT forced at 0.9 × V_OUT(nom), V_IN = V_OUT(nom) + 2.0V	350	500	625	mA
I_SC	Short-circuit current limit	R_LOAD = 20 mΩ	30	50	75	mA
I_PLIMIT	Current limit at max headroom	V_IN = 40V, V_OUT = 1.2V	35			mA
V_HEADROOM	Max headroom at full load	V_OUT = 1.2V	15			V
I_FB	Feedback current	V_IN = 40V	-10		10	nA
I_Q	Quiescent current	3.0V ≤ V_IN ≤ V_OUT – 0.2V , I_OUT = 0mA		12	25	μA
		I_OUT = 0mA		2.8	5.2
		V_OUT + 0.5V ≤ V_IN ≤ 40V , I_OUT = 0mA			7.6
I_GND	Ground current	I_OUT = 1mA		16.5	20	μA
I_GND	Ground current	V_IN = V_OUT + 2.0V, I_OUT = 300mA			600	μA
I_SHUTDOWN	Shutdown current	V_EN = 0V, T_J = 25℃		0.45		μA
I_SHUTDOWN	Shutdown current	V_OUT + 0.5V ≤ V_IN ≤ 40V , V_EN = 0V			1.25	μA
T_start-up	Start-up time	V_IN, V_EN tied together, V_IN ramped to V_OUT(nom) + 0.5V, I_OUT = 0mA		500		μs
I_EN	EN pin current	0V ≤ V_EN ≤ 40V, V_IN and V_EN tied together			0.5	μA
I_EN	EN pin current	0V ≤ V_IN ≤ 40V, V_EN = 0V			0.5	μA
V_IL(EN)	EN pin low-level input voltage (disable device)				0.5	V
V_IH(EN)	EN pin high-level input voltage (enable device)		1.1			V
V_HYST(EN)	EN pin hysteresis (enable device)			0.11		V
PSRR	Power-supply ripple rejection	V_IN – V_OUT = 3.0 V, I_OUT = 300mA, f = 100kHz		45		dB
V_n	Output noise voltage	Bandwidth = 10Hz to 100kHz, V_IN – V_OUT = 3.0 V, I_OUT = 300mA		650		μ_VRMS
T_sd+	Thermal shutdown temperature increasing	Shutdown, temperature increasing	163			°C
T_sd-	Thermal shutdown temperature decreasing	Reset, temperature decreasing	150			°C
R_Discharge	Output discharge resistance	V_IN = 3.0V, V_EN = 0V, T_J = 25℃, I_OUT = 1mA		750		?
I_SINK	Sink current on output	V_OUT = V_OUT × 1.05, T_J = 25℃		3		mA