ZHCSFI2B July   2016  – February 2017 TPS53667

PRODUCTION DATA.  

1. 1 特性
2. 2 應用范圍
3. 3 說明
4. 4 修訂歷史記錄
5. 5 Pin Configuration and Functions
6. 6 Specifications
   1. 6.1 Absolute Maximum Ratings
   2. 6.2 Handling Ratings
   3. 6.3 Recommended Operating Conditions
   4. 6.4 Thermal Information
   5. 6.5 Electrical Characteristics
   6. 6.6 I/O Timing Requirements
   7. 6.7 Switching Characteristics
   8. 6.8 Typical Characteristics
7. 7 Detailed Description
   1. 7.1 Overview
   2. 7.2 Functional Block Diagram
   3. 7.3 Feature Description
      1. 7.3.1  V3R3 LDO
      2. 7.3.2  PWM Operation
      3. 7.3.3  Current Sense and IMON Calculation
      4. 7.3.4  Setting the Load-Line (DROOP)
      5. 7.3.5  Load Transitions
      6. 7.3.6  Overshoot Reduction (OSR)
      7. 7.3.7  Undershoot Reduction (USR)
      8. 7.3.8  AutoBalance™ Current Sharing
      9. 7.3.9  Phase Overlap
      10. 7.3.10 VID
      11. 7.3.11 PWM and SKIP Signals
      12. 7.3.12 TSEN (Thermal Sense) Pin
      13. 7.3.13 RESET Function
      14. 7.3.14 Input UVLO
      15. 7.3.15 V5 Pin Undervoltage Lockout (UVLO)
      16. 7.3.16 Output Undervoltage Protection (UVP)
      17. 7.3.17 Overvoltage Protection (OVP)
      18. 7.3.18 Overcurrent Limit (OCL) and Overcurrent Protection (OCP)
      19. 7.3.19 Current Sharing Warning and Phase Fault Detect
      20. 7.3.20 Turn off Individual Phase by PMBus
      21. 7.3.21 Phase Shedding
      22. 7.3.22 Over Temperature Protection (OTP)
      23. 7.3.23 VR_HOT and VR_FAULT Indication
   4. 7.4 Device Functional Modes
   5. 7.5 Programming
      1. 7.5.1 User Selections
         1. 7.5.1.1  Switching Frequency
         2. 7.5.1.2  IMAX Information
         3. 7.5.1.3  Boot Voltage
         4. 7.5.1.4  Per-Phase Overcurrent Limit (OCL) Level
         5. 7.5.1.5  Overshoot Reduction (OSR) and Undershoot Reduction (USR) Levels
         6. 7.5.1.6  Slew Rate Selection
         7. 7.5.1.7  Mode Selections
         8. 7.5.1.8  Soft Start Slew Rate and PMBus Addresses
         9. 7.5.1.9  Ramp Selection
         10. 7.5.1.10 Maximum Active Phase Numbers
         11. 7.5.1.11 Pinstrap Mode Settings
         12. 7.5.1.12 NVM Default Settings
         13. 7.5.1.13 6-Phase Application
         14. 7.5.1.14 6-Phase NVM Application
      2. 7.5.2 Supported Protections and Fault Reports
      3. 7.5.3 Supported PMBus Address and Commands Summary
         1. 7.5.3.1 Address Selection
         2. 7.5.3.2 Commands Summary
   6. 7.6 Register Maps
      1. 7.6.1 PMBus Description
         1. 7.6.1.1 PMBus General
         2. 7.6.1.2 PMBus Connections
         3. 7.6.1.3 Supported Data Formats
         4. 7.6.1.4 PMBus Command Format
      2. 7.6.2 PMBus Functionality
         1. 7.6.2.1 PMBus Address
         2. 7.6.2.2 Pin Strap Settings
         3. 7.6.2.3 Supported PMBus Commands
            1. 7.6.2.3.1  OPERATION (01h)
            2. 7.6.2.3.2  ON_OFF_CONFIG (02h)
            3. 7.6.2.3.3  CLEAR_FAULTS (03h)
            4. 7.6.2.3.4  WRITE_PROTECT (10h)
            5. 7.6.2.3.5  STORE_DEFAULT_ALL (11h)
            6. 7.6.2.3.6  RESTORE_DEFAULT_ALL (12h)
            7. 7.6.2.3.7  CAPABILITY (19h)
            8. 7.6.2.3.8  VOUT_MODE (20h)
            9. 7.6.2.3.9  VOUT_COMMAND (21h)
            10. 7.6.2.3.10 VOUT_MAX (24h)
            11. 7.6.2.3.11 VOUT_MARGIN_HIGH (25h)
            12. 7.6.2.3.12 VOUT_MARGIN_LOW (26h)
            13. 7.6.2.3.13 IOUT_CAL_OFFSET (39h)
            14. 7.6.2.3.14 VOUT_OV_FAULT_RESPONSE (41h)
            15. 7.6.2.3.15 VOUT_UV_FAULT_RESPONSE (45h)
            16. 7.6.2.3.16 IOUT_OC_FAULT_LIMIT (46h)
            17. 7.6.2.3.17 IOUT_OC_FAULT_RESPONSE (47h)
            18. 7.6.2.3.18 IOUT_OC_WARN_LIMIT (4Ah)
            19. 7.6.2.3.19 OT_FAULT_LIMIT (4Fh)
            20. 7.6.2.3.20 OT_FAULT_RESPONSE (50h)
            21. 7.6.2.3.21 OT_WARN_LIMIT (51h)
            22. 7.6.2.3.22 VIN_OV_FAULT_LIMIT (55h)
            23. 7.6.2.3.23 IIN_OC_FAULT_LIMIT (5Bh)
            24. 7.6.2.3.24 IIN_OC_FAULT_RESPONSE (5Ch)
            25. 7.6.2.3.25 IIN_OC_WARN_LIMIT (5Dh)
            26. 7.6.2.3.26 STATUS_BYTE (78h)
            27. 7.6.2.3.27 STATUS_WORD (79h)
            28. 7.6.2.3.28 STATUS_VOUT (7Ah)
            29. 7.6.2.3.29 STATUS_IOUT (7Bh)
            30. 7.6.2.3.30 STATUS_INPUT (7Ch)
            31. 7.6.2.3.31 STATUS_TEMPERATURE (7Dh)
            32. 7.6.2.3.32 STATUS_CML (7Eh)
            33. 7.6.2.3.33 STATUS_MFR_SPECIFIC (80h)
            34. 7.6.2.3.34 READ_VIN (88h)
            35. 7.6.2.3.35 READ_IIN (89h)
            36. 7.6.2.3.36 READ_VOUT (8Bh)
            37. 7.6.2.3.37 READ_IOUT (8Ch)
            38. 7.6.2.3.38 READ_TEMPERATURE_1 (8Dh)
            39. 7.6.2.3.39 READ_POUT (96h)
            40. 7.6.2.3.40 READ_PIN (97h)
            41. 7.6.2.3.41 PMBus_REVISION (98h)
            42. 7.6.2.3.42 MFR_ID (99h)
            43. 7.6.2.3.43 MFR_MODEL (9Ah)
            44. 7.6.2.3.44 MFR_REVISION (9Bh)
            45. 7.6.2.3.45 MFR_DATE (9Dh)
            46. 7.6.2.3.46 MFR_VOUT_MIN (A4h)
            47. 7.6.2.3.47 MFR_SPECIFIC_00 (Per-Phase Overcurrent Limit) (D0h)
            48. 7.6.2.3.48 MFR_SPECIFIC_01 (Telemetry Averaging Time) (D1h)
            49. 7.6.2.3.49 MFR_SPECIFIC_04 (Read VOUT) (D4h)
            50. 7.6.2.3.50 MFR_SPECIFIC_05 (VOUT Trim) (D5h)
            51. 7.6.2.3.51 MFR_SPECIFIC_07 (Additional Function Bits) (D7h)
            52. 7.6.2.3.52 MFR_SPECIFIC_08 (Droop) (D8h)
            53. 7.6.2.3.53 MFR_SPECIFIC_09 (OSR/USR) (D9h)
            54. 7.6.2.3.54 MFR_SPECIFIC_10 (Maximum Operating Current) (DAh)
            55. 7.6.2.3.55 MFR_SPECIFIC_11 (VBOOT) (DBh)
            56. 7.6.2.3.56 MFR_SPECIFIC_12 (Switching Frequency and TRISE) (DCh)
            57. 7.6.2.3.57 MFR_SPECIFIC_13 (Slew Rate and Other Operation Modes) (DDh)
            58. 7.6.2.3.58 MFR_SPECIFIC_14 (Ramp Height) (DEh)
            59. 7.6.2.3.59 MFR_SPECIFIC_15 (Dynamic Phase Shedding Thresholds) (DFh)
            60. 7.6.2.3.60 MFR_SPECIFIC_16 (VIN UVLO) (E0h)
            61. 7.6.2.3.61 MFR_SPECIFIC_19 (E3h)
            62. 7.6.2.3.62 MFR_SPECIFIC_20 (Maximum Operational Phase Number) (E4h)
            63. 7.6.2.3.63 MFR_SPECIFIC_21 (VIN UVLO) (E5h)
            64. 7.6.2.3.64 MFR_SPECIFIC_22 ( VOUT_UV_FAULT_threshold) (E6h)
            65. 7.6.2.3.65 MFR_SPECIFIC_23 (E7h)
            66. 7.6.2.3.66 MFR_SPECIFIC_24 (E8h)
            67. 7.6.2.3.67 MFR_SPECIFIC_44 (DEVICE_CODE) (FCh)
8. 8 Application and Implementation
   1. 8.1 Application Information
   2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
         1. 8.2.2.1  Select the Switching Frequency
         2. 8.2.2.2  Set the Maximum Output Current (IMAX)
         3. 8.2.2.3  Select the Soft-Start Slew Rate
         4. 8.2.2.4  Select the Operation Mode
         5. 8.2.2.5  Choose Inductor
         6. 8.2.2.6  Select the Per-Phase Valley Current Limit And Ramp Level
         7. 8.2.2.7  Set the Load-Line
         8. 8.2.2.8  Set the BOOT Voltage
         9. 8.2.2.9  Set OSR/USR Thresholds to Improve Load Transient Performance
         10. 8.2.2.10 Digital Current Monitor (IMON) Gain and Filter Setting
         11. 8.2.2.11 Compensation Design
         12. 8.2.2.12 Set PMBus Addresses
         13. 8.2.2.13 Programming the Device with the PMBus
      3. 8.2.3 Application Curves
9. 9 Power Supply Recommendations
10. 10Layout
    1. 10.1 Layout Guidelines
       1. 10.1.1 Schematic Review Checklist
       2. 10.1.2 PCB Design Guidelines
          1. 10.1.2.1 Layer Stack-up, 8-Layer PCB as example
          2. 10.1.2.2 Current Sensing Lines
          3. 10.1.2.3 Feedback Voltage Sensing Lines
          4. 10.1.2.4 PWM Lines
          5. 10.1.2.5 Power Chain Symmetry
          6. 10.1.2.6 Placing Analog Signal Components
          7. 10.1.2.7 Grounding Recommendations
          8. 10.1.2.8 TI Smart Power Stage CSD95490Q5MC
             1. 10.1.2.8.1 Electrical Performance
             2. 10.1.2.8.2 Thermal Performance
             3. 10.1.2.8.3 Sensing Performance
          9. 10.1.2.9 Power Delivery and Power Density
    2. 10.2 Layout Example
11. 11器件和文檔支持
    1. 11.1 器件支持
       1. 11.1.1 Third-Party Products Disclaimer
       2. 11.1.2 開發支持
    2. 11.2 文檔支持
       1. 11.2.1 相關文檔
    3. 11.3 接收文檔更新通知
    4. 11.4 社區資源
    5. 11.5 商標
    6. 11.6 靜電放電警告
    7. 11.7 Glossary
12. 12機械、封裝和可訂購信息