最新地址2019入口一,欧美人又长又大又粗无码视频一区

ZHCSA11H May 2012 – September 2024 TCA9548A

PRODUCTION DATA

封裝選項

機械數據 (封裝 | 引腳)

DGS|24
- MPSS138
PW|24
- MPDS363A
RGE|24
- MPQF124G

散熱焊盤機械數據 (封裝 | 引腳)

RGE|24
- QFND024AD

訂購信息

5.5 Electrical Characteristics

V_CC = 1.65 V to 5.5 V, over recommended operating free-air temperature ranges supported by Recommended Operating Conditions (unless otherwise noted) ⁽¹⁾

PARAMETER			TEST CONDITIONS	V_CC	MIN	TYP ⁽²⁾	MAX	UNIT
V_PORR	Power-on reset voltage, V_CC rising		No load, V_I = V_CC or GND⁽³⁾			1.2	1.5	V
V_PORF	Power-on reset voltage, V_CC falling⁽⁴⁾		No load, V_I = V_CC or GND⁽³⁾		0.8	1		V
V_o(sw)	Switch output voltage		V_i(sw) = V_CC, I_SWout = –100 μA	5 V		3.6		V
				4.5 V to 5.5 V	2.6		4.5
				3.3 V		1.9
				3 V to 3.6 V	1.6		2.8
				2.5 V		1.5
				2.3 V to 2.7 V	1.1		2
				1.8 V		1.1
				1.65 V to 1.95 V	0.6		1.25
I_OL	SDA		V_OL = 0.4 V	1.65 V to 5.5 V	3	6		mA
I_OL	SDA		V_OL = 0.6 V	1.65 V to 5.5 V	6	9		mA
I_I	SCL, SDA		V_I = V_CC or GND⁽³⁾	1.65 V to 5.5 V	–1		1	μA
	SC7–SC0, SD7–SD0				–1		1
	A2–A0				–1		1
	RESET				–1		1
I_CC	Operating mode	f_SCL = 400 kHz	V_I = V_CC or GND⁽³⁾, I_O = 0	5.5 V		50	80	μA
				3.6 V		20	35
				2.7 V		11	20
				1.65 V		6	10
		f_SCL = 100 kHz	V_I = V_CC or GND⁽³⁾, I_O = 0	5.5 V		9	30
				3.6 V		6	15
				2.7 V		4	8
				1.65 V		2	4
	Standby mode	Low inputs	V_I = GND⁽³⁾, I_O = 0, -40 ℃ ≤ TA ≤ 85 ℃	5.5 V		0.2	2
				3.6 V		0.1	2
				2.7 V		0.1	1
				1.65 V		0.1	1
		High inputs	V_I = V_CC, I_O= 0, -40 ℃ ≤ TA ≤ 85 ℃	5.5 V		0.2	2
				3.6 V		0.1	2
				2.7 V		0.1	1
				1.65 V		0.1	1
		Low and High Inputs	Vi = Vcc or GND, Io = 0, 85 ℃ < TA ≤ 125 ℃	3.6 V		1	2	μA
				2.7 V		0.7	1.5	μA
				1.65 V		0.4	1	μA
ΔI_CC	Supply-current change	SCL, SDA	SCL or SDA input at 0.6 V, Other inputs at V_CC or GND⁽³⁾	1.65 V to 5.5 V		3	20	μA
ΔI_CC	Supply-current change	SCL, SDA	SCL or SDA input at V_CC – 0.6 V, Other inputs at V_CC or GND⁽³⁾	1.65 V to 5.5 V		3	20	μA
C_i	A2–A0		V_I = V_CC or GND⁽³⁾	1.65 V to 5.5 V		4	5	pF
	RESET		V_I = V_CC or GND⁽³⁾			4	5
	SCL		V_I = V_CC or GND⁽³⁾, Switch OFF			20	28
C_io(off)⁽⁵⁾	SDA		V_I = V_CC or GND⁽³⁾, Switch OFF	1.65 V to 5.5 V		20	28	pF
C_io(off)⁽⁵⁾	SC7–SC0, SD7–SD0		V_I = V_CC or GND⁽³⁾, Switch OFF	1.65 V to 5.5 V		5.5	7.5	pF
R_ON	Switch-on resistance		V_O = 0.4 V, I_O = 15 mA	4.5 V to 5.5 V	4	10	20	?
			V_O = 0.4 V, I_O = 15 mA	3 V to 3.6 V	5	12	30
			V_O = 0.4 V, I_O = 10 mA	2.3 V to 2.7 V	7	15	45
			V_O = 0.4 V, I_O = 10 mA	1.65 V to 1.95 V	10	25	70

(1) For operation between specified voltage ranges, refer to the worst-case parameter in both applicable ranges

(2) All typical values are at nominal supply voltage (1.8-, 2.5-,3.3-, or 5-V V_CC), T_A = 25°C

(3) RESET = V_CC (held high) when all other input voltages, V_I = GND.

(4) The power-on reset circuit resets the I²C bus logic with V_CC< V_PORF

(5) C_io(ON)depends on internal capacitance and external capacitance added to the SCn lines when channels(s) are ON.