WWW.一本色道88久久爱,欧美内射深喉中文字幕

ZHCSNJ3I October 2005 – June 2022 PCA9546A

PRODUCTION DATA

封裝選項

機械數據 (封裝 | 引腳)

DGV|16
- MPDS006C
DW|16
- MSOI003I
PW|16
- MPDS361B
RGY|16
- MPQF115G
D|16
- MPDS178G
RGV|16
- MPQF121F

散熱焊盤機械數據 (封裝 | 引腳)

DW|16
- QFND313D
RGY|16
- QFND040P
RGV|16
- QFND107G

訂購信息

6.6 I²C Interface Timing Requirements

over recommended operating free-air temperature range (unless otherwise noted) (see Figure 7-1)

			MIN	MAX	UNIT
I²C BUS—STANDARD MODE
f_scl	I²C clock frequency		0	100	kHz
t_sch	I²C clock high time		4		μs
t_scl	I²C clock low time		4.7		μs
t_sp	I²C spike time			50	ns
t_sds	I²C serial-data setup time		250		ns
t_sdh	I²C serial-data hold time		0⁽¹⁾		ns
t_icr	I²C input rise time			1000	ns
t_icf	I²C input fall time			300	ns
t_ocf	I²C output fall time	10-pF to 400-pF bus		300	ns
t_buf	I²C bus free time between stop and start		4.7		μs
t_sts	I²C start or repeated start condition setup		4.7		μs
t_sth	I²C start or repeated start condition hold		4		μs
t_sps	I²C stop condition setup		4		μs
t_vdL(Data)	Valid data time (high to low)⁽²⁾	SCL low to SDA output low valid		1	μs
t_vdH(Data)	Valid data time (low to high)⁽²⁾	SCL low to SDA output high valid		0.6	μs
t_vd(ack)	Valid data time of ACK condition	ACK signal from SCL low to SDA (out) low		1	μs
C_b	I²C bus capacitive load			400	pF

(1) A device internally must provide a hold time of at least 300 ns for the SDA signal (referred to the V_IH min of the SCL signal), in order to bridge the undefined region of the falling edge of SCL.

(2) Data taken using a 1-k? pull-up resistor and 50-pF load (see Figure 7-1)

			MIN	MAX	UNIT
I²C BUS—FAST MODE
f_scl	I²C clock frequency		0	400	kHz
t_sch	I²C clock high time		0.6		μs
t_scl	I²C clock low time		1.3		μs
t_sp	I²C spike time			50	ns
t_sds	I²C serial-data setup time		100		ns
t_sdh	I²C serial-data hold time		0⁽¹⁾		ns
t_icr	I²C input rise time		20 + 0.1C_b ⁽²⁾	300	ns
t_icf	I²C input fall time		20 + 0.1C_b ⁽²⁾	300	ns
t_ocf	I²C output fall time	10-pF to 400-pF bus	20 + 0.1C_b ⁽²⁾	300	ns
t_buf	I²C bus free time between stop and start		1.3		μs
t_sts	I²C start or repeated start condition setup		0.6		μs
t_sth	I²C start or repeated start condition hold		0.6		μs
t_sps	I²C stop condition setup		0.6		μs
t_vdL(Data)	Valid data time (high to low)⁽³⁾	SCL low to SDA output low valid		1	μs
t_vdH(Data)	Valid data time (low to high)⁽³⁾	SCL low to SDA output high valid		0.6
t_vd(ack)	Valid data time of ACK condition	ACK signal from SCL low to SDA (out) low		1	μs
C_b	I²C bus capacitive load			400	pF

(2) C_b = total bus capacitance of one bus line in pF

(3) Data taken using a 1-k? pull-up resistor and 50-pF load (see Figure 7-1)

封裝選項

機械數據 (封裝 | 引腳)

散熱焊盤機械數據 (封裝 | 引腳)

訂購信息

6.6 I2C Interface Timing Requirements

6.6 I²C Interface Timing Requirements