国产免费踩踏视频网,男生J桶进女人P又色又爽又黄 ,91精品婷婷国产综合久久

ZHCSQG1H November 2009 – May 2022 LMP8645 , LMP8645HV

PRODUCTION DATA

封裝選項

機械數據 (封裝 | 引腳)

DDC|6
- MPDS124I

散熱焊盤機械數據 (封裝 | 引腳)

訂購信息

6.7 12-V Electrical Characteristics

Unless otherwise specified, all limits specified for at T_A = 25°C, V_S = V⁺ – V^-, V⁺ = 12 V, V^? = 0 V, ?2 V < V_CM < 76 V, R_g= 25 k?, R_L = 10 M?.⁽¹⁾

PARAMETER		TEST CONDITIONS		MIN⁽³⁾	TYP⁽²⁾	MAX⁽³⁾	UNIT
V_OS	Input Offset Voltage	V_CM = 2.1 V		–1		1	mV
V_OS	Input Offset Voltage	V_CM = 2.1 V	At the temperature extremes	–1.7		1.7	mV
TCV_OS	Input Offset Voltage Drift⁽⁴⁾⁽⁶⁾	V_CM = 2.1 V				7	μV/°C
I_B	Input Bias Current⁽⁷⁾	V_CM = 2.1 V			13	23	μA
e_ni	Input Voltage Noise⁽⁶⁾	f > 10 kHz, R_G = 5 k?			120		nV/√ Hz
V_SENSE(MAX)	Max Input Sense Voltage⁽⁶⁾	V_CM = 12 V, R_G = 5 k?			600		mV
Gain A_V	Adjustable Gain Setting⁽⁶⁾	V_CM = 12 V		1		100	V/V
Gm	Transconductance	V_CM = 2.1 V			200		μA/V
	Accuracy	V_CM = 2.1 V		–2%		2%
	Accuracy	V_CM = 2.1 V	At the temperature extremes	–3.4%		3.4%
	Gm drift⁽⁶⁾	?40°C to 125°C, V_CM = 2.1 V				140	ppm /°C
PSRR	Power Supply Rejection Ratio	V_CM = 2.1 V, 2.7 V <V⁺ < 12 V		90			dB
CMRR	Common-Mode Rejection Ratio	LMP8645HV 2.1 V < V_CM < 76 V LMP8645 2.1 V < V_CM< 42 V		95			dB
CMRR	Common-Mode Rejection Ratio	–2 V < V_CM < 2 V		60			dB
BW	?3-dB Bandwidth⁽⁶⁾	R_G = 10 k?, C_G = 4 pF, V_SENSE = 400 mV, C_L = 30 pF, R_L = 1 M?			860		kHz
		R_G = 25 k?, C_G = 4 pF, V_SENSE = 400 mV, C_L = 30 pF, R_L = 1 M?			260
		R_G = 50 k?, C_G = 4 pF, V_SENSE = 400 mV, C_L = 30 pF, R_L = 1 M?			140
SR	Slew Rate⁽⁵⁾ ⁽⁶⁾	V_CM = 5 V, C_G = 4 pF, V_SENSE from 100 mV to 500 mV, C_L = 30 pF, R_L = 1 M?			0.6		V/μs
I_S	Supply Current	V_CM = 2.1 V			555	765	uA
		V_CM = 2.1 V	At the temperature extremes			920
		V_CM = ?2 V			2200	2900
		V_CM = ?2 V	At the temperature extremes			3110
V_OUT	Maximum Output Voltage	V_CM = 12 V, R_G= 500 k?		10.2			V
V_OUT	Minimum Output Voltage	V_CM = 2.1 V				24	mV
I_OUT	Output current⁽⁶⁾	Sourcing, V_OUT = 5.25 V, Rg = 150 k?			5		mA
I_OUT	Output current⁽⁶⁾	Sinking, V_OUT = 5.25 V, Rg = 150 k?			5		mA
C_LOAD	Max Output Capacitance Load⁽⁶⁾				30		pF

(1) Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very limited self-heating of the device such that T_J = T_A. No specification of parametric performance is indicated in the electrical tables under conditions of internal self-heating where T_J > T_A.

(2) Typical values represent the most likely parametric norm at the time of characterization. Actual typical values may vary over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped production material.

(3) All limits are specified by testing, design, or statistical analysis.

(4) Offset voltage temperature drift is determined by dividing the change in V_OS at the temperature extremes by the total temperature change.

(5) The number specified is the average of rising and falling slew rates and measured at 90% to 10%.

(6) This parameter is specified by design and/or characterization and is not tested in production.

(7) Positive Bias Current corresponds to current flowing into the device.