ZHCSLD0B May   2020  – June 2021 LM62435-Q1

PRODUCTION DATA  

1. 1 特性
2. 2 應用
3. 3 說明
4. 4 Revision History
5. 5 Device Comparison Table
6. 6 Pin Configuration and Functions
7. 7 Specifications
   1. 7.1 Absolute Maximum Ratings
   2. 7.2 ESD Ratings
   3. 7.3 Recommended Operating Conditions
   4. 7.4 Thermal Information
   5. 7.5 Electrical Characteristics
   6. 7.6 計時特性
   7. 7.7 Systems Characteristics
   8. 7.8 Typical Characteristics
8. 8 Detailed Description
   1. 8.1 Overview
   2. 8.2 Functional Block Diagram
   3. 8.3 Feature Description
      1. 8.3.1  EN Uses for Enable and VIN UVLO
      2. 8.3.2  MODE/SYNC Pin Operation
         1. 8.3.2.1 Level-Dependent MODE/SYNC Pin Control
         2. 8.3.2.2 Pulse-Dependent MODE/SYNC Pin Control
         3. 8.3.2.3 Clock Locking
      3. 8.3.3  PGOOD Output Operation
      4. 8.3.4  Internal LDO, VCC UVLO, and BIAS Input
      5. 8.3.5  Bootstrap Voltage and VCBOOT-UVLO (CBOOT Pin)
      6. 8.3.6  Adjustable SW Node Slew Rate
      7. 8.3.7  Spread Spectrum
      8. 8.3.8  Soft Start and Recovery From Dropout
      9. 8.3.9  Output Voltage Setting
      10. 8.3.10 Overcurrent and Short Circuit Protection
      11. 8.3.11 Thermal Shutdown
      12. 8.3.12 Input Supply Current
   4. 8.4 Device Functional Modes
      1. 8.4.1 Shutdown Mode
      2. 8.4.2 Standby Mode
      3. 8.4.3 Active Mode
         1. 8.4.3.1 CCM Mode
         2. 8.4.3.2 Auto Mode - Light Load Operation
            1. 8.4.3.2.1 Diode Emulation
            2. 8.4.3.2.2 Frequency Reduction
         3. 8.4.3.3 FPWM Mode - Light Load Operation
         4. 8.4.3.4 Minimum On-time (High Input Voltage) Operation
         5. 8.4.3.5 Dropout
9. 9 Application and Implementation
   1. 9.1 Application Information
   2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
         1. 9.2.2.1  Choosing the Switching Frequency
         2. 9.2.2.2  Setting the Output Voltage
         3. 9.2.2.3  Inductor Selection
         4. 9.2.2.4  Output Capacitor Selection
         5. 9.2.2.5  Input Capacitor Selection
         6. 9.2.2.6  BOOT Capacitor
         7. 9.2.2.7  BOOT Resistor
         8. 9.2.2.8  VCC
         9. 9.2.2.9  BIAS
         10. 9.2.2.10 CFF and RFF Selection
         11. 9.2.2.11 External UVLO
      3. 9.2.3 Application Curves
10. 10Power Supply Recommendations
11. 11Layout
    1. 11.1 Layout Guidelines
       1. 11.1.1 Ground and Thermal Considerations
    2. 11.2 Layout Example
12. 12Device and Documentation Support
    1. 12.1 Documentation Support
       1. 12.1.1 Related Documentation
    2. 12.2 接收文檔更新通知
    3. 12.3 支持資源
    4. 12.4 Trademarks
    5. 12.5 靜電放電警告
    6. 12.6 術語表
13. 13Mechanical, Packaging, and Orderable Information