Product details

Rating Automotive Number of series cells (max) 26 Number of series cells (min) 9 Features AEC-Q100 Automotive Qual, ASIL-D, Cell balancing, Electrochemical Impedance Spectroscopy (EIS) Engine, High precision, I2C support, Integrated ADC, Multi-cell support, Open-wire detection, Over-Voltage Protection, Overtemperature protection, Separate MCU requirement, Stackable (built-in interface), Temperature sensing, Under Voltage Protection, Undertemperature protection Vin (max) (V) 145 Communication interface Daisy chain, I2C controller, SPI Operating temperature range (°C) to Battery overvoltage protection (min) (V) 2.7 Battery overvoltage protection (max) (V) 5.1 TI functional safety category Functional Safety-Compliant
Rating Automotive Number of series cells (max) 26 Number of series cells (min) 9 Features AEC-Q100 Automotive Qual, ASIL-D, Cell balancing, Electrochemical Impedance Spectroscopy (EIS) Engine, High precision, I2C support, Integrated ADC, Multi-cell support, Open-wire detection, Over-Voltage Protection, Overtemperature protection, Separate MCU requirement, Stackable (built-in interface), Temperature sensing, Under Voltage Protection, Undertemperature protection Vin (max) (V) 145 Communication interface Daisy chain, I2C controller, SPI Operating temperature range (°C) to Battery overvoltage protection (min) (V) 2.7 Battery overvoltage protection (max) (V) 5.1 TI functional safety category Functional Safety-Compliant
HTQFP (PZS) 100 196 mm2 14 x 14
  • 26 Channels
    • 26S – 0 to 5.5V range for cell, -2V to 2V range for busbar
    • 143V Abs Max Rating, 9V minimum
    • Busbar support on every channel, except first channel.
    • Stackable up to 128 devices
  • Voltage Accuracy
    • <1.7 mV accuracy, -40 to 125C, Cell: 0V to 5.5V
    • Dedicated ADC per channel. Synchronized redundant measurement.
  • Passive Cell Balancing with integrated FETs up to 300mA odd/even balancing with programmable PWM control
  • Smart EIS Engine
    • Integrated Electrochemical Impedance Spectroscopy measurement engine
    • Impedance Accuracy: 1% (with 1A excitation and 200uΩ impedance)
    • Measurement frequency: 0.01Hz to 3.5kHz
    • < 5us I/V synchronization from device to device
    • Support for global and local excitation
  • Sensor & GPIOs
    • 20 GPIO: Temp Sensor (NTC/PTC), voltage measurement, Interrupt
    • SPI / I2C Interface
    • Temperature Threshold (Active / Sleep)
    • Pressure Threshold / Peak Detector (Active / Sleep)
    • On-chip memory for one-time custom programming
  • Diagnostics & Protection
    • Monitoring
      • Low Power Monitoring Mode (<20uA power consumption)
      • Cell Over-voltage, Under-voltage (OVUV)
      • Cell Over-temperature, Under-temperature (OTUT)
      • 2x die temperature monitors
      • Supply (BAT)
      • Open Wire Detection
    • Reverse Wake Up based on selectable faults
    • Redundancy Paths
      • Cell Voltage
      • GPIO/NTC Voltage
      • Limp Home Mode
    • Diagnostics
      • Automatic diagnostics during cell balancing in active mode
    • Functional Safety Compliant
      • Developed under ISO26262
      • System and hardware capability up to ASIL-D
  • Upgraded Daisy Chain Interface
    • 2Mbps bus speed, Up to 4Mbps with dual SPI
    • <+/-5us device to device synchronization
    • Closed Loop BCI: 200mA, Open Loop BCI: 300mA
    • Isolation: Transformer or capacitor-only
    • FDTI Time: <100ms for 800V packs or 250 cells
    • Support for stack, ring, multidrop, and split-ring
    • Device-to-device automatic communications balancing
  • Power
    • Integrated DC-DC Converter
    • Shutdown: <10uA
    • Sleep Mode with monitoring: As low as 20uA
    • Active Mode: <5mA
  • Package
    • 100-pin QFP, 4mm pitch
    • PowerPad on bottom
  • 26 Channels
    • 26S – 0 to 5.5V range for cell, -2V to 2V range for busbar
    • 143V Abs Max Rating, 9V minimum
    • Busbar support on every channel, except first channel.
    • Stackable up to 128 devices
  • Voltage Accuracy
    • <1.7 mV accuracy, -40 to 125C, Cell: 0V to 5.5V
    • Dedicated ADC per channel. Synchronized redundant measurement.
  • Passive Cell Balancing with integrated FETs up to 300mA odd/even balancing with programmable PWM control
  • Smart EIS Engine
    • Integrated Electrochemical Impedance Spectroscopy measurement engine
    • Impedance Accuracy: 1% (with 1A excitation and 200uΩ impedance)
    • Measurement frequency: 0.01Hz to 3.5kHz
    • < 5us I/V synchronization from device to device
    • Support for global and local excitation
  • Sensor & GPIOs
    • 20 GPIO: Temp Sensor (NTC/PTC), voltage measurement, Interrupt
    • SPI / I2C Interface
    • Temperature Threshold (Active / Sleep)
    • Pressure Threshold / Peak Detector (Active / Sleep)
    • On-chip memory for one-time custom programming
  • Diagnostics & Protection
    • Monitoring
      • Low Power Monitoring Mode (<20uA power consumption)
      • Cell Over-voltage, Under-voltage (OVUV)
      • Cell Over-temperature, Under-temperature (OTUT)
      • 2x die temperature monitors
      • Supply (BAT)
      • Open Wire Detection
    • Reverse Wake Up based on selectable faults
    • Redundancy Paths
      • Cell Voltage
      • GPIO/NTC Voltage
      • Limp Home Mode
    • Diagnostics
      • Automatic diagnostics during cell balancing in active mode
    • Functional Safety Compliant
      • Developed under ISO26262
      • System and hardware capability up to ASIL-D
  • Upgraded Daisy Chain Interface
    • 2Mbps bus speed, Up to 4Mbps with dual SPI
    • <+/-5us device to device synchronization
    • Closed Loop BCI: 200mA, Open Loop BCI: 300mA
    • Isolation: Transformer or capacitor-only
    • FDTI Time: <100ms for 800V packs or 250 cells
    • Support for stack, ring, multidrop, and split-ring
    • Device-to-device automatic communications balancing
  • Power
    • Integrated DC-DC Converter
    • Shutdown: <10uA
    • Sleep Mode with monitoring: As low as 20uA
    • Active Mode: <5mA
  • Package
    • 100-pin QFP, 4mm pitch
    • PowerPad on bottom
Download View video with transcript Video
Request more information

The full data sheet is available. Request now

The functional safety documents are available. Request now

Technical documentation

star =Top documentation for this product selected by TI
No results found. Please clear your search and try again.
View all 1
Type Title Date
* Data sheet BQ79826Z-Q1 Automotive 26S/24S Battery Monitor with Smart EIS Engine datasheet PDF | HTML 29 Sep 2025

Design & development

For additional terms or required resources, click any title below to view the detail page where available.

Evaluation board

BQ79826Q1EVM-086 — BQ79826Z-Q1 evaluation module

The BQ79826Z-Q1 Evaluation Module (EVM), also referred to as BMS086, describes the general features, theory of operation, hardware setup, and use of TI's BQ79826Z-Q1 device. The BQ79826ZQ1 device is a highly integrated stackable 26- cell monitor with up to 300mA passive balancing current (...)

Request
Driver or library

BQ79826-Q1-DESIGN — BQ79826Z-Q1 design resources

BQ79826Z-Q1 Document Repository
Supported products & hardware

Supported products & hardware

Products
Battery monitors & balancers
BQ79826Z-Q1 — Automotive 26-S battery monitor and balancer with Electrochemical Impedance Spectroscopy engine
Driver or library

EIS-BQ798XX-Q1-DESIGN — BQ798XX-Q1 Electrochemical Impedance Spectroscopy Design resources

EIS design secure folder for BQ798XX-Q1
Supported products & hardware

Supported products & hardware

Products
Battery monitors & balancers
BQ79826Z-Q1 — Automotive 26-S battery monitor and balancer with Electrochemical Impedance Spectroscopy engine BQ79881-Q1 — Automotive battery junction box pack monitor with Electrochemical Impedance Spectroscopy
Package Pins CAD symbols, footprints & 3D models
HTQFP (PZS) 100 Ultra Librarian

Ordering & quality

Information included:
  • RoHS
  • REACH
  • Device marking
  • Lead finish/Ball material
  • MSL rating/Peak reflow
  • MTBF/FIT estimates
  • Material content
  • Qualification summary
  • Ongoing reliability monitoring
Information included:
  • Fab location
  • Assembly location

Recommended products may have parameters, evaluation modules or reference designs related to this TI product.

Support & training

TI E2E? forums with technical support from TI engineers

Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.

If you have questions about quality, packaging or ordering TI products, see TI support. ??????????????

Videos