ZHCSCQ0 August   2014 TPS25921A , TPS25921L

PRODUCTION DATA.  

1. 1 特性
2. 2 應用范圍
3. 3 說明
4. 4 應用電路原理圖
5. 5 修訂歷史記錄
6. 6 Pin Configuration and Functions
7. 7 Specifications
   1. 7.1 Absolute Maximum Ratings
   2. 7.2 Handling Ratings
   3. 7.3 Recommended Operating Conditions
   4. 7.4 Thermal Characteristics
   5. 7.5 Electrical Characteristics
   6. 7.6 Timing Requirements
   7. 7.7 Typical Characteristics
8. 8 Parametric Measurement Information
9. 9 Detailed Description
   1. 9.1 Overview
   2. 9.2 Functional Block Diagram
   3. 9.3 Feature Description
      1. 9.3.1 Enable and Adjusting Undervoltage Lockout (UVLO)
      2. 9.3.2 Overvoltage Protection (OVP)
      3. 9.3.3 Hot Plug-in and In-Rush Current Control
      4. 9.3.4 Overload and Short Circuit Protection :
         1. 9.3.4.1 Overload Protection
         2. 9.3.4.2 Short Circuit Protection
         3. 9.3.4.3 Start-Up with Short on Output
         4. 9.3.4.4 Constant Current Limit Behavior during Overcurrent Faults
      5. 9.3.5 FAULT Response
      6. 9.3.6 IN, OUT and GND Pins
      7. 9.3.7 Thermal Shutdown:
   4. 9.4 Device Functional Modes
      1. 9.4.1 Shutdown Control
      2. 9.4.2 Operational Overview of Device Functions
10. 10Applications and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
       1. 10.2.1 Precision Current Limiting and Protection for White Goods
          1. 10.2.1.1 Design Requirements
          2. 10.2.1.2 Detailed Design Procedure
             1. 10.2.1.2.1 Step by Step Design Procedure
             2. 10.2.1.2.2 Programming the Current-Limit Threshold: R(ILIM) Selection
             3. 10.2.1.2.3 Undervoltage Lockout and Overvoltage Set Point
             4. 10.2.1.2.4 Setting Output Voltage Ramp time (tSS)
                1. 10.2.1.2.4.1 Case1: Start-up Without Load: Only Output Capacitance C(OUT) Draws Current During Start-up
                2. 10.2.1.2.4.2 Case 2: Start-up With Load: Output Capacitance C(OUT) and Load Draws Current During Start-up
             5. 10.2.1.2.5 Support Component Selections - R4 and CIN
          3. 10.2.1.3 Application Curves
11. 11System Examples
    1. 11.1 Protection and Current Limiting for Primary-Side Regulated Power Supplies
    2. 11.2 Precision Current Limiting in Intrinsic Safety Applications
    3. 11.3 Smart Load Switch
12. 12Power Supply Recommendations
    1. 12.1 Transient Protection
    2. 12.2 Output Short-Circuit Measurements
13. 13Layout
    1. 13.1 Layout Guidelines
    2. 13.2 Layout Example
14. 14器件和文檔支持
    1. 14.1 相關鏈接
    2. 14.2 Trademarks
    3. 14.3 Electrostatic Discharge Caution
    4. 14.4 術語表
15. 15機械封裝和可訂購信息