成人午夜被窝福利,久久AV无码乱码A片无码软件,丁香五月婷婷基地亚洲综合

ZHCSIQ5A September 2018 – August 2021 LM34936

PRODUCTION DATA

封裝選項

機械數據 (封裝 | 引腳)

RHF|28
- MPQF251C

散熱焊盤機械數據 (封裝 | 引腳)

RHF|28
- QFND264B

訂購信息

6.5 Electrical Characteristics

Typical values correspond to T_J = 25°C. Minimum and maximum limits apply over the –40°C to 125°C junction temperature range unless otherwise stated. V_IN = 24 V unless otherwise stated.⁽¹⁾

PARAMETER		TEST CONDITION	MIN	TYP	MAX	UNIT
SUPPLY VOLTAGE (V_IN)
I_Q	V_IN shutdown current	V_EN/UVLO = 0 V		2.6	10	μA
	V_IN operating current	V_EN/UVLO = 2 V, V_FB = 0.9 V		2	4	mA
VCC
V_VCC(VIN)	Regulation voltage	V_BIAS = 0 V, VCC open	6.95	7.35	7.88	V
V_UV(VCC)	VCC Undervoltage lockout	VCC increasing	3.11	3.27	3.43	V
	Undervoltage hysteresis			176		mV
I_VCC	VCC current limit	V_VCC = 0 V	65			mA
R_OUT(VCC)	VCC regulator output impedance	I_VCC = 30 mA, V_IN = 4 V		8	16	Ω
BIAS
V_BIAS(SW)	BIAS switchover voltage	V_IN = 24 V	7.25	8	8.75	V
EN/UVLO
V_EN(STBY)	Standby threshold	EN/UVLO rising	0.55	0.82	0.97	V
I_EN(STBY)	Standby source current	V_EN/UVLO = 1.1 V	1	2	3	μA
V_EN(OP)	Operating threshold	EN/UVLO rising	1.17	1.22	1.29	V
ΔI_HYS(OP)	Operating hysteresis current	V_EN/UVLO = 1.5 V	2.15	3.15	4.25	μA
SS
I_SS	Soft-start pull up current	V_SS = 0 V	3.75	5	6.35	μA
V_SS(CL)	SS clamp voltage	SS open		1.21		V
V_FB - V_SS	FB to SS offset	V_SS = 0 V		-18		mV
EA (ERROR AMPLIFIER)
V_REF	Feedback reference voltage	FB = COMP	0.788	0.800	0.812	V
gm_EA	Error amplifier gm			1.31		mS
I_SINK/I_SOURCE	COMP sink/source current	V_FB=V_REF ± 300 mV		280		μA
R_OUT	Amplifier output resistance			20		M?
BW	Unity gain bandwidth			2		MHz
I_BIAS(FB)	Feedback pin input bias current	FB in regulation			25	nA
FREQUENCY
f_SW(1)	Switching Frequency 1	RT = 40 k?	175	200	225	kHz
f_SW(2)	Switching Frequency 2	RT = 20 k?	350	390	430	kHz
DITHER
I_DITHER	Dither source/sink current			11		μA
V_DITHER	Dither high threshold			1.27		V
	Dither low threshold			1.16		V
SYNC
V_SYNC	Sync input high threshold		2.1			V
	Sync input low threshold				1.2	V
PW_SYNC	Minimum sync input pulse width		50			ns
CURRENT LIMIT
V_CS(BUCK)	Buck current limit threshold (Valley)	V_IN = V_VISNS = 24 V, V_VOSNS = 12 V, V_SLOPE = 0 V	60	80	94	mV
V_CS(BOOST)	Boost current limit threshold (Peak)	V_IN = V_VISNS = 12 V, V_VOSNS = 18 V, V_SLOPE = 0 V	96	120	140	mV
I_BIAS(CS/CSG)	CS/CSG pin bias current	V_CS = V_CSG = 0 V		-80		μA
I_{OFFSET(CS/CSG)}	CSG pin bias current	V_CS = V_CSG = 0 V			19	μA
CONSTANT CURRENT LOOP
V_SNS	Average current loop regulation target	V_ISNS(-) = 24 V, sweep ISNS(+), V_SS = 0.8 V	43	50	57	mV
I_SNS	ISNS(+)/ISNS(–) pin bias currents	V_ISNS(+) = V_ISNS(–) = V_IN = 24 V		3		μA
Gm	gm of soft-start pull down amplifier	V_ISNS(+)–V_ISNS(–) = 55 mV, V_SS = 0.5 V		1		mS
SLOPE
I_SLOPE	Buck adaptive slope current	V_IN = V_VISNS = 24 V, V_VOSNS = 12 V, V_SLOPE = 0 V	24	30	35	μA
	Boost adaptive slope current	V_IN = V_VISNS = 12 V, V_VOSNS = 18 V, V_SLOPE = 0 V	13	17	21	μA
gm_SLOPE	Slope compensation amplifier gm			2		μS
MODE
I_MODE	Source current out of MODE pin		17	20	23	μA
V_{CCM_HIC}	CCM with hiccup threshold		1.18	1.28	1.38	V
V_CCM	CCM no hiccup threshold		2.22	2.4	2.6	V
PGOOD
V_PGD	PGOOD trip threshold for falling FB	Measured with respect to V_REF		–9		%
	PGOOD trip threshold for rising FB	Measured with respect to V_REF		10		%
	Hysteresis			2.5		%
I_LEAK(PGD)	PGOOD leakage current				100	nA
I_SINK(PGD)	PGOOD sink current	V_PGOOD = 0.4 V	2	4.2	6.5	mA
OUTPUT OVP
V_OVP	Output overvoltage threshold at FB pin	Measured with respect to V_REF		10		%
	Hysteresis			2.5		%
NMOS DRIVERS
I_HDRV1,2	Driver peak source current	V_BOOT - V_SW = 7 V		1.8		A
	Driver peak sink current	V_BOOT - V_SW = 7 V		2.2
I_LDRV1,2	Driver peak source current			1.8
	Driver peak sink current			2.2
R_HDRV1,2	Driver pull up resistance	V_BOOT - V_SW = 7 V		1.8		?
	Driver pull down resistance	V_BOOT - V_SW = 7 V		1.1		?
V_UV(BOOT1,2)	BOOT1,2 to SW1,2 UVLO threshold	HDRV1,2 shut off		3.4		V
	BOOT1,2 to SW1,2 UVLO hysteresis	HDRV1,2 start switching		150		mV
R_LDRV1,2	Driver pull up resistance			1.7		?
	Driver pull down resistance			1.3		?
t_DT1	Dead time HDRV1,2 off to LDRV1,2 on			45		ns
t_DT2	Dead time LDRV1,2 off to HDRV1,2 on			45		ns
THERMAL SHUTDOWN
T_SD	Thermal shutdown temperature			165		°C
T_SD(HYS)	Thermal shutdown hysteresis			15		°C

(1) All minimum and maximum limits are specified by correlating the electrical characteristics to process and temperature variations and applying statistical process control.